Description
Republic Lagun 55″ x 10″ Vertical Knee Mill, FTV-2F
Inventory # 6411
Model: FTV-2F
Specifications:
Table:
Table Size: 55.25″ x 10″
T-Slots: 3 on 2 1/2″ Centers
T-Slot Size: 5/8″
Max. Weight on Table: 750 lbs.
Travels:
Table Travel, X-Axis, Manual/Power Feed: 38 1/2″ / 35″ – 37″
Cross Travel, Y-Axis: 16″
Knee Travel, Z-Axis: 16″
Ram Travel: 22 3/16″
Head:
Speed: 55 – 4,250 RPM.
Low Speed: 55 – 490 RPM
High Speed: 490 – 4,250 RPM
Head Swivel: +/- 90°
Head Tilt: +/- 45°
Distance, Spindle to Column: 5″ – 27″
Distance, Spindle to Table: 0 – 18″
Quill:
Power Quill Feeds: .0015″, .003″, .006″
Spindle Taper: R-8
Quill Diameter: 3 3/8″
Quill Travel: 5″
Machine Constructive Dimensions:
Collet Turret Diameter: 15″
Knee Width: 11 1/2″
Knee to Column Bearing Length: 18″
Saddle and Table Bearing Length: 23″
Ram and Turret Bearing Length: 19″
Ram Length: 36″
Motor: 5 HP / 230v, 440v / 3ph
Standard Equipment:
Flood Coolant System
Hardened and Precision Ground Ways
One Shot Lubrication System
Draw Bar
Operators Manual/Parts List
Basic Service Tool Kit
Standard Features:
Fully enclosed head will keep dust from shop environment out; keeping critical parts and components clean and dust free
Two speed ranges 5 HP constant drive, mechanical infinite variable speeds, and dynamically balanced head reaches full horsepower over all the speed range without the typical losses characteristic of EVS systems. This head is capable of reaching 358’/lbs. of torque
Special high performance transmission belt. The heard of our mechanical infinite variable speed milling head uses the same hi-technology found in the continuously variable transmission of the latest hybrid automobiles
3 3/8″ quill is hard chromed with precision ground rack
Spindle taper is R-8 with four hi-precision class 7 bearings
The head assembly can be tilted front-to-back and swiveled right-to-left. Angular settings emply worm and gear
Ram/head assembly can be easily rotated a full 360°
Massive ram features 19″ of bearing length and 22 3/16″ travel
The ram design allows use of optional slotting attachment mounted opposite the standard head
All lead screws are thread rolled and precision ground
A uniqe double nut assembly provides backlash adjustment of longitudinal and cross feed screws. Adjustment of this device eliminates backlash due to wear
Table and saddle locks are conveniently located in front of the machine. Handles are spring loaded to allow repositioning once locked. This advance design clamps the table to the saddle, does not push on a gib. As a result, the table will hold its position more accurate
The 11 1/2″ wide knee has square and dovetail way guides. This combination provides the rigidity of the square way design and retains the accuracy of the dovetail design. Ways are hardened and ground
The saddle has full 23″ of bearing length supporting the table, allowing work-piece weights up to 750 lbs.
The one-shot central lubrication systel provides oil to all sliding surfaces, nuts, and lead screws
Anti-friction turcite type bearings surface material is used throughout the machine
A flood coolant system pump is located on top of base inside the column. The base acts as a reservoir. Access is through column opening
Single source power for machine; main power disconnect; electric enclosure with low voltage trasnformer, motor starter for main motor with over and under voltage protections for machine and operator. Push buttons for stop and e-stop; selector switch (forward/reverse) for main motor. Four 110v plug-ins (for power feed, read out, light, etc.), coolant pump fused on/off switch
Mechanical Specifications:
Dimensions: 67″ x 63″ x 104″ H
Weight: approx. 2,850 lbs.
FOB Factory – Contact us for Pricing and Availability